Total Items in Cart:  0    Total Amount: $0.00


SME Model 20/3A


(image for) Call for Price


This finely engineered precision turntable is built to the same exacting standard and incorporates many design features originated for the Model 20/12. Massive construction, extensional damping of major surfaces and lack of vibration from moving parts ensures exceptional detail, resolution and uncoloured performance.

A turntable should address the problems of extraneous vibrations. These emanate from numerous sources including air and structural vibration from loudspeakers, groove modulation, stray electrical fields and mechanical imperfections in moving parts. In the Model 20/3, superb instrument quality machining is allied with fundamental physics. The higher the mass and stiffness of a body the less it will flex and vibrate; the duration of a vibration can be shortened by suitable damping.

Model 20/3 weighs approximately 28.6Kg (63lb), significant in  relation to its size because it is density that matters. For example, the same weight of metal spread over a large enough area would be aluminium foil! The sub-chassis measures only 440mm (17 5/16”) by 350mm (13 ¾”) but weighs 11Kg (24lb). Its thickness 16mm (5/8”) resists flexing at low frequencies whilst high frequency resonance is attenuated by efficient extensional damping.

The Model 20/3 has no `sonic footprint'. The subchassis is suspended on forty purpose moulded ‘O’ rings which ensure freedom from feedback. The method of anchorage allows the rings to be removed or replaced in a matter of moments, even whilst a record is playing. A large centrally placed damper disciplines sub-chassis movement.

In addition to a cartridge’s electrical output, mirror image acoustic signals reacted in the arm and record, will pass into the sub-chassis in the course of dissipation. However the usual closed loop design does not address the problem of their differing phase so in the Model 20/3 the structural interfaces concerned have received special attention to provide paths of the required impedance. This control of vibration is fundamental to the design of the player and goes much of the way to explaining the stunning tonal and dynamic neutrality that it exhibits.

The turntable is driven by a 3 phase, brushless outrunner inductance motor with 8-pole Neodymium magnets and 3 integrated Hall position sensors. The electronic controller uses a high performance microprocessor, optimised for motor control. Closed loop speed control is implemented using a proportional plus integral (PI) algorithm. Fine pitch speed adjustment allows increments/decrements of +/-0.01% of selected speed. Speed ranges: 33 1/3, 45 & 78 rpm.

Mains voltages available are 90-110V, 105-125V and 220-240V 50/60Hz. Please specify when ordering.

The Model 20/3 is available in two formats:

MODEL 20/3
equipped for but not including SME precision pick-up arm.

MODEL 20/3A
as above but complete with matching SME Series V precision pick-up arm. Complete with a comprehensive set of tools and equipment including Height Setting Gauge, Ø300mm Stroboscopic Disc, Reflex Record Clamp, Record Spindle Washer, Soft Cover and Operating Instruction Manual.

Dimensions: 440 x 350 x 172mm.
Packing: Substantial case.
Net weight with power supply: 31Kg (68lb)
Shipping weight approximately: 45Kg (100lb)
  • Four point suspension for stability.
  • Sub-chassis suspended on eighty strands of rubber in the form of forty purpose moulded ‘O rings.
  • Suspension adjustable through trimmers used in conjunction with a gauge to give recommended settingsor varied to suit individual conditions.
  • Central fluid damper controls sub-chassis motion and offers resistive ground-path for acoustic signals.
  • Two screws lock down the sub-chassis and seal the damper for transport.
  • 19mm diameter main spindle machined from high - chrome steel, hardened, ground and super finished runs in a sealed oil bath for lifetime lubrication.
  • Screw down reflex record clamping system minimises record resonance.
  • 6.5Kg (14lb) platter with unique Isodamp face machined with a fine scroll for optimum record interface.
  • Generous use of extensional damping and resistive loop construction ensure sonic neutrality.
  • Optional mounting on steel ball feet or compliant inserts, both affording levelling adjustment.
  • Four jacking screws built into the sub-platter allow the thrust bearing to be off loaded for transit.
  • The Power Supply design incorporates a 4-layer surface mount technology pcb with on-board user adjustable speed variation control.
  • Large diameter strobe disc supplied allows precise adjustment of standard speeds.
  • Speed range: 33 1/3, 45 & 78 rpm.
  • Fully shielded in-line control unit. LEDs indicate themain functions

100 % Money Back Guarantee !

As with all the products we sell. If your not 110% happy with the products & services you receive from us we will give you a 100% money back guarantee. On not only the price of the product but as well the cost of the shipping. That�s how confident we are in all the products we sell.


Full Ten Year Warranty !

When you purchase any of our new production SME products.

Be it tonearms or turntables we give you a full ten year warranty.

Bumper to bumper !

Short of leaving your turntable in the garden over the winter or using your tonearm as a pry bar to open a can of paint, we will cover what ever goes wrong with your newly purchased SME product.

All we ask is that you retain your original receipt.

We realize and understand that you have made an enormous investment in your analogue playback system & we want to reassure you that we will be there to stand behind it.

The warranty we offer is unmatched and unrivaled in the analogue playback industry.

We here at www.smetonearms.com have been rebuilding, rewiring & restoring SME arms for almost fifteen years now and SME England has been in business building tonearms & turntables for well over fifty years now & counting.

I don't think either of us are going away !

Welcome to our hugely successful SME Trade In & Trade Up Program.

For more than a decade now our SME Trade In & Trade Up Program
has enabled our clients to move to higher level SME arms while getting more
than fair market value for their old SME tone arms.

How it works is simple.

You own an older SME arm and wish to move to a newer more advanced SME arm
or higher up the SME ladder.

Not a problem.

Simply give us a call or send us an email & within a few short minutes
you own a new SME tone arm or turntable at a wonderfully discounted price.

We buy back your well loved SME arm or SME table and you get a brand new in the factory sealed box SME arm or SME table complete with our industry exclusive ten year warranty.

Here are the trade in allowances we will give for your vintage SME tone arms.

SME 3012 Series I – up to $1,500.00
SME 3009 Series I – up to $1,000.00
SME 3012 Series II – up to $1,000.00
SME 3009 Series II – up to $500.00
SME 3009 Series II Improved – up to $500.00
SME 3012-R – up to $1,200.00
SME 3010-R – up to $800.00
SME 3009-R – up to $700.00
SME Series III – up to $500.00

We will also buy your older SME arms outright if you do not wish to trade your vintage SME arm in against a new replacement SME arm.

Simply give us a call at 705-737-6773 or send us off an email through our contact section.


Copyright © 2024 SME Tonearms. Powered by Zen Cart